Garage door opener installation can be successfully accomplished even without professional help. All you need is a little know how and the assistance of the right tools. However, bear in mind that the installation requirements of different models of garage openers vary greatly. Hence why, you should read its manual carefully to ascertain that you'll be able to properly carry out the task. But in general, here are the steps that you have to follow when installing a garage door opener. First and foremost, be sure to prepare the materials that will be needed to properly install the opener. This will likely include the following: Garage door opener set Mounting brackets Drill and drill bits Socket and wrenches Screw driver, hack saw, and hammer Pliers, wire cutter, and level Tape measure Basically, there are different types of rails used in garage door repair Glendale CA. Newer models typically use T-shaped rail. If you happen to purchase an opener using the T-shape rail, the first thing that you should do is to properly align the T-shape rail in place. Once done, be sure to securely bolt them together. After which, align the idler pulley and then secure it at the end of the guide rail of the door opener. Next, get the trolley and then carefully slide it unto the rails so you can now bolt the rail on the door opener. Slip a screwdriver in the hole of the trolley to secure it in place. Then, attach one of end of the belt chain using the included hardware. Be sure to wrap the chain around the idler pulley and also around the opener's sprocket. After that, attach the chain to the other side of the pulley. You need to open the garage door to determine the highest point that the door needs to travel above the installed tracks. Be sure to add 2 inches in the acquired measurement. The marked area is where you will place the opener's header bracket. Once you have attached the head bracket, close the door and then connect it to the end of the idler pulley's assembly. Make certain that you lift the pulley assembly to ensure that the rail is above the opener's track. Again, open the door and raise the door opener until it is 2 inches above the door; do this with the use of shims. Get the mounting bracket and connect it to the existing joists in the garage ceiling using the lag screws. And then, attach the door opener to the bracket with the aid of the mounting brackets that come with the unit. After which, install the door controls and other remaining components to complete the garage opener installation. Finally, test the garage door if it is fully functional. Article Source
0 Comments
There are many reasons why a garage door repair Pearland TX, . The most common reason is that the track line is misaligned. Another reason is that the chain is either too tight or too loose. Garage door springs are another common ailment that will ultimately kill a garage door opener if not maintained. Lets go into a few of these reason in detail and share with you some of the solutions.
First of all lets talk about what happens to your door opener if the tracks are misaligned. Misaligned tracks cause the door not to roll up and down smoothly and evenly. The whole point of of having the tracks is to put the least amount of resistance on the door opener motor unit. If the tracks have been damaged or become uneven, bad pressure will be put on the garage door opener. This extra resistance is very bad on the motor and will ultimately burn it out. Most motor burnouts are caused by this simple issue of making sure your tracks are stable and aligned to minimize door resistance. Tracks are super easy to fix and maintain. They are made of aluminum or steel tracks and brackets can be adjusted very easily with the turn of the screw. If the track is wiggling or shifting, simply add a few more support brackets which will cost you only a few dollars at a hardware store. The second garage killer is the chain itself. Yearly maintenance on the chain will help your garage door motor to last for a very long time. If the chain is too loose it will cause the motor to slip and get out of its rhythm. If the chain has slipped and the door opens faster than normal the motor will continue to turn according to its timer. If the motor continues to run once its open you will burn out the motor because its like putting a brick wall in front of a moving car, its just not good. Simple tightening or loosening the spring will adjust the tightness of the chain. Make sure the chain is tight, meaning no slack, but don't over tighten it as it will put additional pressure on the sprocket mechanism. Article Source: http://EzineArticles.com/2537984
There are many common garage door issues that may occur with the system at your home. The complications are typically associated with the garage door opener that controls the opening and closing of the door. It is important that you learn as much as you are able about the door opener that your door depends on.
This includes learning about the parts, how they work, and how to overcome obstacles associated with the parts. Many individuals experience the issue of the remote and the switch installed on the wall not opening the door as it should. If you experience this common complication, you should know that it is related to the source of power. This means it could be as simple as a fuse or even a circuit breaker. If you try to close the garage door and you find that it does not reach the ground, it could be an issue with the limit settings on closing. In some instances, lifting it and then simply re closing it will do the trick. In other cases, you may need a garage door repair Avon CT, to come out and take a look at the switch that controls the close limit area. There are many that will experience just the opposite - a door that will not open all the way. If you experience this, the switch that controls the limits of the door may need to be mounted in an area that is closer to the motor itself. Do you find that when the garage door starts to close it hits a point where it starts to go in reverse without any direction from you? If so, the force that is used to close the door may need some adjustments. This is best done by a specialist. There are a large number of door issues that may occur. It is important to know that many of these situations can be resolved by simple adjustments, however, in some instances, it is best to incorporate the knowledge of a garage door repair specialist. Article Source: http://EzineArticles.com/3110518 |